You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
141 lines
5.1 KiB
141 lines
5.1 KiB
# Read GPS data - Wio Terminal
|
|
|
|
In this part of the lesson, you will add a GPS sensor to your Wio Terminal, and read values from it.
|
|
|
|
## Hardware
|
|
|
|
The Wio Terminal needs a GPS sensor.
|
|
|
|
The sensor you'll use is a [Grove GPS Air530 sensor](https://www.seeedstudio.com/Grove-GPS-Air530-p-4584.html). This sensor can connect to multiple GPS systems for a fast, accurate fix. The sensor is made of 2 parts - the core electronics of the sensor, and an external antenna connected by a thin wire to pick up the radio waves from the satellites.
|
|
|
|
This is a UART sensor, so sends GPS data over UART.
|
|
|
|
### Connect the GPS sensor
|
|
|
|
The Grove GPS sensor can be connected to the Wio Terminal.
|
|
|
|
#### Task - connect the GPS sensor
|
|
|
|
Connect the GPS sensor.
|
|
|
|
|
|
|
|
1. Insert one end of a Grove cable into the socket on the GPS sensor. It will only go in one way round.
|
|
|
|
1. With the Wio Terminal disconnected from your computer or other power supply, connect the other end of the Grove cable to the left-hand side Grove socket on the Wio Terminal as you look at the screen. This is the socket closest to the power button.
|
|
|
|
|
|
|
|
1. Position the GPS sensor so that the attached antenna has visibility to the sky - ideally next to an open window or outside. It's easier to get a clearer signal with nothing in the way of the antenna.
|
|
|
|
1. You can now connect the Wio Terminal to your computer.
|
|
|
|
1. The GPS sensor has 2 LEDs - a blue LED that flashes when data is transmitted, and a green LED that flashes every second when receiving data from satellites. Ensure the blue LED is flashing when you power up the Wio Terminal. After a few minutes the green LED will flash - if not, you may need to reposition the antenna.
|
|
|
|
## Program the GPS sensor
|
|
|
|
The Wio Terminal can now be programmed to use the attached GPS sensor.
|
|
|
|
### Task - program the GPS sensor
|
|
|
|
Program the device.
|
|
|
|
1. Create a brand new Wio Terminal project using PlatformIO. Call this project `gps-sensor`. Add code in the `setup` function to configure the serial port.
|
|
|
|
1. Add the following include directive to the top of the `main.cpp` file. This includes a header file with functions to configure the left-hand Grove port for UART.
|
|
|
|
```cpp
|
|
#include <wiring_private.h>
|
|
```
|
|
|
|
1. Below this, add the following line of code to declare a serial port connection to the UART port:
|
|
|
|
```cpp
|
|
static Uart Serial3(&sercom3, PIN_WIRE_SCL, PIN_WIRE_SDA, SERCOM_RX_PAD_1, UART_TX_PAD_0);
|
|
```
|
|
|
|
1. You need to add some code to redirect some internal signal handlers to this serial port. Add the following code below the `Serial3` declaration:
|
|
|
|
```cpp
|
|
void SERCOM3_0_Handler()
|
|
{
|
|
Serial3.IrqHandler();
|
|
}
|
|
|
|
void SERCOM3_1_Handler()
|
|
{
|
|
Serial3.IrqHandler();
|
|
}
|
|
|
|
void SERCOM3_2_Handler()
|
|
{
|
|
Serial3.IrqHandler();
|
|
}
|
|
|
|
void SERCOM3_3_Handler()
|
|
{
|
|
Serial3.IrqHandler();
|
|
}
|
|
```
|
|
|
|
1. In the `setup` function below where the `Serial` port is configured, configure the UART serial port with the following code:
|
|
|
|
```cpp
|
|
Serial3.begin(9600);
|
|
|
|
while (!Serial3)
|
|
; // Wait for Serial3 to be ready
|
|
|
|
delay(1000);
|
|
```
|
|
|
|
1. Below this code in the `setup` function, add the following code to connect the Grove pin to the serial port:
|
|
|
|
```cpp
|
|
pinPeripheral(PIN_WIRE_SCL, PIO_SERCOM_ALT);
|
|
```
|
|
|
|
1. Add the following function before the `loop` function to send the GPS data to the serial monitor:
|
|
|
|
```cpp
|
|
void printGPSData()
|
|
{
|
|
Serial.println(Serial3.readStringUntil('\n'));
|
|
}
|
|
```
|
|
|
|
1. In the `loop` function, add the following code to read from the UART serial port and print the output to the serial monitor:
|
|
|
|
```cpp
|
|
while (Serial3.available() > 0)
|
|
{
|
|
printGPSData();
|
|
}
|
|
|
|
delay(1000);
|
|
```
|
|
|
|
This code reads from the UART serial port. The `readStringUntil` function reads up until a terminator character, in this case a new line. This will read a whole NMEA sentence (NMEA sentences are terminated with a new line character). All the while data can be read from the UART serial port, it is read and sent to the serial monitor via the `printGPSData` function. Once no more data can be read, the `loop` delays for 1 second (1,000ms).
|
|
|
|
1. Build and upload the code to the Wio Terminal.
|
|
|
|
1. Once uploaded, you can monitor the GPS data using the serial monitor.
|
|
|
|
```output
|
|
> Executing task: platformio device monitor <
|
|
|
|
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
|
|
--- More details at http://bit.ly/pio-monitor-filters
|
|
--- Miniterm on /dev/cu.usbmodem1201 9600,8,N,1 ---
|
|
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
|
|
$GNGGA,020604.001,4738.538654,N,12208.341758,W,1,3,,164.7,M,-17.1,M,,*67
|
|
$GPGSA,A,1,,,,,,,,,,,,,,,*1E
|
|
$BDGSA,A,1,,,,,,,,,,,,,,,*0F
|
|
$GPGSV,1,1,00*79
|
|
$BDGSV,1,1,00*68
|
|
```
|
|
|
|
> 💁 You can find this code in the [code-gps/wio-terminal](code-gps/wio-terminal) folder.
|
|
|
|
😀 Your GPS sensor program was a success!
|