You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
98 lines
3.7 KiB
98 lines
3.7 KiB
# Detect proximity - Raspberry Pi
|
|
|
|
In this part of the lesson, you will add a proximity sensor to your Raspberry Pi, and read distance from it.
|
|
|
|
## Hardware
|
|
|
|
The Raspberry Pi needs a proximity sensor.
|
|
|
|
The sensor you'll use is a [Grove Time of Flight distance sensor](https://www.seeedstudio.com/Grove-Time-of-Flight-Distance-Sensor-VL53L0X.html). This sensor uses a laser ranging module to detect distance. This sensor has a range of 10mm to 2000mm (1cm - 2m), and will report values in that range pretty accurately, with distances above 1000mm reported as 8109mm.
|
|
|
|
The laser rangefinder is on the back of the sensor, the opposite side to the Grove socket.
|
|
|
|
This is an I<sup>2</sup>C sensor.
|
|
|
|
### Connect the time of flight sensor
|
|
|
|
The Grove time of flight sensor can be connected to the Raspberry Pi.
|
|
|
|
#### Task - connect the time of flight sensor
|
|
|
|
Connect the time of flight sensor.
|
|
|
|
|
|
|
|
1. Insert one end of a Grove cable into the socket on the time of flight sensor. It will only go in one way round.
|
|
|
|
1. With the Raspberry Pi powered off, connect the other end of the Grove cable to one of the I<sup>2</sup>C sockets marked **I<sup>2</sup>C** on the Grove Base hat attached to the Pi. These sockets are on the bottom row, the opposite end to the GPI pins and next to the camera cable slot.
|
|
|
|
|
|
|
|
## Program the time of flight sensor
|
|
|
|
The Raspberry Pi can now be programmed to use the attached time of flight sensor.
|
|
|
|
### Task - program the time of flight sensor
|
|
|
|
Program the device.
|
|
|
|
1. Power up the Pi and wait for it to boot.
|
|
|
|
1. Open the `fruit-quality-detector` code in VS Code, either directly on the Pi, or connect via the Remote SSH extension.
|
|
|
|
1. Create a new file in this project called `distance-sensor.py`.
|
|
|
|
> 💁 An easy way to simulate multiple IoT devices is to do each in a different Python file, then run them at the same time.
|
|
|
|
1. Add the following code to this file:
|
|
|
|
```python
|
|
import time
|
|
|
|
from grove.i2c import Bus
|
|
from rpi_vl53l0x.vl53l0x import VL53L0X
|
|
```
|
|
|
|
This imports the Grove I<sup>2</sup>C bus library, and a sensor library for the core sensor hardware built into the Grove time of flight sensor.
|
|
|
|
1. Below this, add the following code to access the sensor:
|
|
|
|
```python
|
|
distance_sensor = VL53L0X(bus = Bus().bus)
|
|
distance_sensor.begin()
|
|
```
|
|
|
|
This code declares a distance sensor using the Grove I<sup>2</sup>C bus, then starts the sensor.
|
|
|
|
1. Finally, add an infinite loop to read distances:
|
|
|
|
```python
|
|
while True:
|
|
distance_sensor.wait_ready()
|
|
print(f'Distance = {distance_sensor.get_distance()} mm')
|
|
time.sleep(1)
|
|
```
|
|
|
|
This code waits for a value to be ready to read from the sensor, then prints it to the console.
|
|
|
|
1. Run this code.
|
|
|
|
> 💁 Don't forget this file is called `distance-sensor.py`! Make sure to run this via Python, not `app.py`.
|
|
|
|
1. You will see distance measurements appear in the console. Position objects near the sensor and you will see the distance measurement:
|
|
|
|
```output
|
|
pi@raspberrypi:~/fruit-quality-detector $ python3 distance_sensor.py
|
|
Distance = 29 mm
|
|
Distance = 28 mm
|
|
Distance = 30 mm
|
|
Distance = 151 mm
|
|
```
|
|
|
|
The rangefinder is on the back of the sensor, so make sure you use the correct side when measuring distance.
|
|
|
|
|
|
|
|
> 💁 You can find this code in the [code-proximity/pi](code-proximity/pi) folder.
|
|
|
|
😀 Your proximity sensor program was a success! |